12/16/2022 0 Comments Manually uninstall my lockboxThis will not reset the lock or disconnect it from the app. Press down while turning the latch counterclockwise to release the latch from the back plate. Use a pen or similar to enter the hole on the top as shown in the drawing below. If you need to disassemble / remove your smart lock, do the following: To reset the lock, click 10 times, wait 5 seconds. You can cancel your selection by clicking 7 times. Put the smart lock in unlocked position and leave the door open when auto-calibrating. Then turn the lock to locked position and click 1 time to save.Īuto-calibration. Click twice and wait 5 seconds until it blinks yellow. The lock will flash green and you have 30 seconds to search your smart lock in Wattle. To connect your smart lock to Wattle, click once and wait for five seconds. The lock has a button available through a small hole (on top of the lock when mounted on the door). The three most common types of cylinders are oval locking cylinders, drop-shaped euro cylinders and deadbolt locks.ĭanalock does not fit on surface mounted door lock or lock cylinder lock. The Smart Lock is designed to fit standard doors throughout the world. Note: Leave the door open so that the lock is not affected when calibrated. One click will enable the green LED light indicating that the lock is ready to connect to Wattle. Put the door lock in discovery mode by pressing a small pin in the door of the door lock. ![]() Note: If the batteries are disconnected you will have to re-calibrate the door lock. A light will flash to confirm that the door lock is ready. Pull out the plastic tab to activate the batteries. Turn the door lock clockwise until it clicks to fasten it to the back plate. Now you’re sure to hit the notches on the back plate with the door lock. Find the small mark on the edge of the back plate and adjust it with the hole in the cover ring surrounding the door lock. Fit the door lock over the back plate with the battery cover facing down,the tail piece sliding into the adapter and the back plate notches into the back of the lock. Press the adapter until a click ensures that it is fixed firmly to the door lock. Take the green tail piece adapter from the door lock box and insert the tail piece adapter in the center tube on the backside of the door lock. Use pliers or a bite to shorten the tail piece. To avoid damage to the door and lock, shorten the tail piece to a maximum of 35 mm from the door panel. Make sure the tail piece is the correct length. Adjust the length as needed. Alternatively, you can use the old screws if they fit better. Use the two breakable long screws to secure the backing plate. The round hole in the middle is for the tail piece. Place the back plate where the twist used to be. Locate the back plate and remove the paper from the three stickers on the back of the back plate. Fit the tail piece with the tail piece plate and the short screws. You must shorten the tail piece after mounting the tail piece plate as shown in step 5. ![]() If the tail piece exceeds 35 mm, you must shorten it.(See illustration in step 7). The door lock can be fitted with a tail piece length of up to 35mm. If the tail piece is less than 10mm from the door panel, use the supplied tail piece found in the box.ī) Some locks have a cylinder and when removed, use the cylinder pin and cylinder plate included in the box. They will fit on the new smart door lock without the need for any adjustment of the length. Most doors have a tail piece that extends 10mm from the door panel. You reinstall them in step 6.Ī) Normal tail piece length. First you need to remove the lock on the inside (the handle). This will hold it in place as you remove the screws on the inside. Before removing your existing lock, use tape to secure the outside keyhole. Make sure you have all the parts ready to install the door lock. Required tool: Philips screwdriver and two pliers or wire cutters. Select the room you want from the list or add a new room. Remove tape from batteries(alternative press the button one time for inclusion-green light)Ĭlick “configure” when door lock are found in the scan. Instructions Get started Scan for Door lock Lock and unlock your door remotely with Wattle.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |